The Beeline provider, in order to keep up with others, decided to release its own router, the connection to the networks of this operator can be configured in a couple of clicks. The router offered under the name Smart Box is built on a unified Realtek 8197D processor and is equipped with 64 MB of memory.
In fact, all the complaints that there may be about the operation of this device relate rather to the firmware. We hope it will be fixed soon. Let's look at how a branded Beeline router needs to be configured, and also how to update its firmware.
Router "Beeline Smart Box"
On the rear panel, in addition to the standard set of ports and the power button, you see an operating mode switch. The “router” mode is activated when the toggle switch knob is in the up position. The second mode is “switch”.
We will look at how to set up a connection with the Beeline provider. To do this, you can connect a computer to the router via a patch cord or by wireless network(which works in mixed mode b/g/n, it is given the name “Smart_box-…”). Finally, we will look at how to update the firmware. The firmware version current at the time of creation of the review is 2.0.19.
Connection setup
As is easy to understand, you need to connect the Beeline cord connector to the WAN port. You can access the router’s web interface from a wired or Wi-Fi network (the latter works without a password).
The actions should be as follows: having connected all the cables, supply power to the router, wait 1 minute, open the web interface. The requirement for setting up a network card is to set the “automatic” mode:
Setting up a wired connection on your computer
On wireless cards, they also enable a similar mode (“auto” DNS and IP). The parameter values needed to open the web interface are given below.
How to open the GUI?
If a wired network is used to configure the router, the patch cord is connected to one of the LAN ports. In order for the network card to receive IP and DNS from the router, you need to right-click on the connection icon and click “Fix”. You can connect to a wireless network without a password; its name is “Smart_box-XXXXXX”.
Let us remind you that the router takes at least a minute to load. The graphical interface address of Smart Box is standard and equal to 192.168.1.1. The default password is the same as the login, this is the word admin:
Login to GUI
Setting up a connection with Beeline
While on the start tab of the interface, click the “Quick setup” button. The following page will open:
Connection setup
Here you need to set the parameters:
- Subscriber login of the form “089XXXXXX” (read the contract)
- The subscriber's password is what is specified in the contract
- “Network name” – you can leave it as is
- “Password” – the value of the Wi-Fi password (you don’t have to use it at first)
- We will not enable the guest Wi-Fi network
- Select one LAN port for the TV set-top box, if required (just not the one that is currently in use)
- Click “Save”
Firmware update
The built-in program for the router, that is, the firmware, can be downloaded from the official Beeline website. The firmware file takes 16 or 17 megabytes. Save it to your “desktop”. Next, we will look at how to reinstall the firmware in a Smart Box router, and most importantly, how not to make it worse.
Preliminary actions
It is best to perform a factory reset before updating the firmware. Turn on the router, wait 2 minutes, press reset with a paperclip (the button must be held for 10-15 seconds). The LEDs should blink, then the router will boot again (but with the default settings).
We will install the firmware by connecting the router to the PC via a wired network. It is necessary. Reinstalling the software is carried out for the sole purpose: to rid the router of the “bugs” of the previous firmware. If everything works well, there is no need to reinstall anything.
It is important to know that while transferring the firmware file, you cannot turn off the power or break the connection between the devices. After the installation is complete, it is better to wait another 5 minutes, and only then briefly press reset.
We update the firmware via the web interface
Go to the configuration GUI as discussed above. On the start tab, click the “Advanced settings” button. Then, select the “Others” tab -> “Software Update”:
Reinstalling the firmware
Sequencing:
- Click “Select file”, find the file on the “desktop” and click “Open”
- Check the connection again and click “Update”
- Wait for the reinstallation to complete
- Wait 5-6 minutes
- Briefly press the reset button on the router
Happy setup!
Router from Beeline SmartBox ONE is a device that is used to distribute traffic when connected to the Internet. You will learn how to configure the router by reading the description below. Such a router costs about 2,500 rubles. An alternative in the absence cable connection is a 4G router ZTE MF90.
Characteristics of the router from Beeline
SmartBox ONE is currently the most new model router from Beeline. One of the advantages of the product is that the device is equipped with a more powerful transmitter capable of operating in two frequency ranges: 5 GHz and 2.4 GHz. This reduces to zero the likelihood that any device used by the user will not be able to connect to the World Wide Web.
The advantages of using the Beeline SmartBox ONE WiFi router also include the following:
- Convenient software interface used to set up a network connection;
- Ergonomic modern design;
- Supports connection to digital TV;
- Maximum data transfer speed – 300 megabits per second;
- The 802.11 standard, which is supported by most modern high-tech devices.
When using a 4G device, data is transmitted at speeds of up to 74 Mbit/second. The device comes complete with a SIM module from Beeline, which provides access to 30 GB of traffic for a month. Subscription fee – 1200 rubles. At night, when connected to a 4G network, there is no limit.
How to set up a 4G/WiFi device from Beeline
There is nothing complicated about connecting a router. The back panel of the product has 7 connectors. You need to connect the power cable from the mains to the Power socket, and the Internet cable that is routed into the apartment to the WAN connector. In the next step, connect the device to the computer by connecting the cable to one of the LAN connectors. The 4G router is connected to a laptop or desktop PC via a USB port.
- After making sure that all the indicators of the Beeline SmartBox ONE router are lit, launch any browser installed on your computer, and enter 192.168.1.1 in the address bar;
- On the welcome page that appears, enter the admin password and the same user name (standard settings) in the appropriate fields, click on the button labeled “Continue”;
- In the main menu that opens, inexperienced users can perform a quick setup procedure, but if they have experience in this regard, they can proceed to the advanced settings.
Easy setup of a Beeline router
If you want to quickly set up a Beeline router, there are 4 points. They are as follows:
- "Home Internet";
- “WiFi network”;
- “Guest network”;
- “TV”.
The “Home Internet” item is used to connect to the Beeline operator network. Since all the required parameters are already contained in the installed software (firmware), the user will only need to enter a password and name (both values are admin).
“WiFi network” is an item in quick settings that gives access to wireless network settings. Here you need to enter in the appropriate fields the name that appears in the connection menu on the devices used, as well as a password of at least 8 characters.
“Guest network” is an item for making settings to provide guest access to the Internet.
The “TV” item is used to select the LAN port to which the cable from the IPTV set-top box, if available, will be connected.
Connecting a router from Beeline
After entering all the required data and making the necessary settings, you need to click on the “Save” button and wait until the device connects to the network. This should take no more than a minute. If everything is done correctly, the “Status” line will display the value “Internet connected”. At this point, all operations are considered completed, and you can proceed to working on the network.
Software update for Beeline router
The software installed by the manufacturer ensures the operation of the router. In order to avoid problems with the router, the firmware should be updated in a timely manner. But you must act with extreme caution when performing such procedures. Otherwise, if something goes wrong, only service center specialists can restore the functionality of the Beeline router.
Important! Software should only be downloaded from the official website.
The process of downloading and installing firmware updates consists of the following steps:
- Launch the browser, enter 192.168.1.1 in the address bar;
- Enter the password and login (admin);
- Go to the advanced settings menu;
- Select the “Other” item at the top of the page; In the window that opens, on the left, click on “Software Update”, and then select the address on the computer where the downloaded software will be located;
- Click on the “Perform update” button.
After a few minutes, the router will reboot and will be ready to function again with the new software.
The firmware of this wonderful router with excellent functionality is not carried out.
- In contact with
- Google+
Connecting a router
Setting up the router
Setting up a router on L2TP
Setting up a router on IPOE
Setting up a router on L2TP
4. « Home Internet»
"Wi-Fi network of the router"
"Guest Wi-Fi network"
Setting up a router on IPOE
1. Open your browser and enter 192.168.1.1 in the address bar. You will be taken to a welcome page. Click Continue.
2. The router will prompt you to enter your username and password. Enter admin in the first field, and admin in the second. Click Continue.
3. You will be taken to the main menu of the router. Select Quick Setup.
4. "Home Internet"
"Wi-Fi network of the router"- here you can configure your router's wireless network. In the Network name field, enter the name of your network, for example my_wifi, and in the Password field, enter the password to access it. Please note that the password must contain at least 8 characters.
"Guest Wi-Fi network"- here you can configure the guest wireless network of your router.
"Beeline" TV - if you have activated the "Beeline" TV service, you need to select the router port to which you will connect the set-top box. If you view over-the-air channels on your computer or using an Xbox 360 console, then you don't need to configure anything.
To save the settings you entered, click the Save button.
Fill the form:
Click the Login button.
Firmware update
Reset
Firmware update
2.0.38: (14.7 MB)
Reset
MCPE
Connecting a router
Connect the cable that our installers installed in your apartment to the Internet (WAN) port, and connect your computer to any of the Ethernet (LAN) ports. You can also connect your PC to the router via a wireless network, but at the initial setup stage it is better to use a cable.
Setting up the router
Setting up a router on L2TP
Setting up a router on IPOE
Setting up a router on L2TP
1. Open your browser and enter 192.168.1.1 in the address bar. You will be taken to a welcome page. Click Continue.
2. The router will prompt you to enter your username and password. Enter admin in the first field, and admin in the second. Click Continue.
3. You will be taken to the main menu of the router. Select Quick Setup.
4. "Home Internet"- in this section you configure the connection to the Beeline network. All configuration data necessary for connection is already contained in the router’s memory; you just need to enter your username and password in the appropriate fields.
"Wi-Fi network of the router"- here you can configure your router's wireless network. In the Network name field, enter the name of your network, for example my_wifi, and in the Password field, enter the password to access it. Please note that the password must contain at least 8 characters.
"Guest Wi-Fi network"- here you can configure the guest wireless network of your router.
"Beeline" TV - if you have activated the "Beeline" TV service, you need to select the router port to which you will connect the set-top box. If you view over-the-air channels on your computer or using an Xbox 360 console, then you don't need to configure anything.
To save the settings you entered, click the Save button.
Setting up a router on IPOE
1. Open your browser and enter 192.168.1.1 in the address bar. You will be taken to a welcome page. Click Continue.
2. The router will prompt you to enter your username and password. Enter admin in the first field, and admin in the second. Click Continue.
3. You will be taken to the main menu of the router. Select Quick Setup.
4. "Home Internet"- in this section you need to enter any number or letter in the “Login” and “Password” fields (the setting does not affect anything).
"Wi-Fi network of the router"- here you can configure your router's wireless network. In the Network name field, enter the name of your network, for example my_wifi, and in the Password field, enter the password to access it. Please note that the password must contain at least 8 characters.
"Guest Wi-Fi network"- here you can configure the guest wireless network of your router.
"Beeline" TV - if you have activated the "Beeline" TV service, you need to select the router port to which you will connect the set-top box. If you view over-the-air channels on your computer or using an Xbox 360 console, then you don't need to configure anything.
To save the settings you entered, click the Save button.
6. Launch the browser, open the page http://login.beeline.ru
Fill the form:
Login - indicate your personal account number (type 0891234567);
Password - enter a password to access the Internet;
Click the Login button.
Firmware update and factory reset
Firmware update
Reset
Firmware update
Be careful when following the instructions in this section. In case of an error in the actions, a visit to the service center will be required to restore the device.
1. Download the firmware. Current firmware version - 2.0.22: (14.5 MB)
2. Open your browser and enter 192.168.1.1 in the address bar. You will be taken to a welcome page. Click Continue.
3. The router will prompt you to enter your username and password. Enter admin in the first field, and admin in the second. Click Continue.
4. Click on the “Advanced Settings” button.
5. In the top menu, select “Others”.
6.A page with the basic settings of the router will open. In the left menu, select “Software Update”. Click the "Select File" button and specify the location of the firmware file that you downloaded earlier.
7. After that, click the “Perform update” button.
8. Wait while the router performs a firmware update, this process takes approximately 5 minutes, after which the router must be rebooted and it will be ready for use.
Reset
Use a hard reset if you need to configure the device again (delete all user settings), there is no access to the web page of the router settings interface, after setting up the router, the Internet connection was not established or the access password was lost.
Attention! When performing a hard reset, all user settings will be reset to factory settings!
There is a recessed RESET (RESTORE) button on the device body, which allows you to reset the settings to factory settings. You can find the RESET, RESTORE button on the same side of the router case where the other connectors and buttons are located. In rare cases, the button may be located on the bottom of the router.
To reset the router to factory settings, follow these steps: Turn on the power to the router and wait until the device boots up completely. Press the RESET, RESTORE button using a pointed thin object (such as a paper clip) for 30 seconds, then release the button.
After this, the router will reboot with default settings (factory settings) and will need to be configured again.
You can also reset the setting through the MCPE platform
Connecting a router
Connect the cable that our installers installed in your apartment to the Internet (WAN) port, and connect your computer to any of the Ethernet (LAN) ports. You can also connect your PC to the router via a wireless network, but at the initial setup stage it is better to use a cable.
Setting up the router
Setting up a router on L2TP
Setting up a router on IPOE
Setting up a router on L2TP
1. Open your browser and enter 192.168.1.1 in the address bar. You will be taken to a welcome page. Click Continue.
2. The router will prompt you to enter your username and password. Enter admin in the first field, and admin in the second. Click Continue.
3. You will be taken to the main menu of the router. Select Quick Setup.
4. "Home Internet"- in this section you configure the connection to the Beeline network. All configuration data necessary for connection is already contained in the router’s memory; you just need to enter your username and password in the appropriate fields.
"Wi-Fi network of the router"- here you can configure your router's wireless network. In the Network name field, enter the name of your network, for example my_wifi, and in the Password field, enter the password to access it. Please note that the password must contain at least 8 characters.
"Guest Wi-Fi network"- here you can configure the guest wireless network of your router.
"Beeline" TV - if you have activated the "Beeline" TV service, you need to select the router port to which you will connect the set-top box. If you view over-the-air channels on your computer or using an Xbox 360 console, then you don't need to configure anything.
To save the settings you entered, click the Save button.
Setting up a router on IPOE
1. Open your browser and enter 192.168.1.1 in the address bar. You will be taken to a welcome page. Click Continue.
2. The router will prompt you to enter your username and password. Enter admin in the first field, and admin in the second. Click Continue.
3. You will be taken to the main menu of the router. Select Quick Setup.
4. "Home Internet"- in this section you need to enter any number or letter in the “Login” and “Password” fields (the setting does not affect anything).
"Wi-Fi network of the router"- here you can configure your router's wireless network. In the Network name field, enter the name of your network, for example my_wifi, and in the Password field, enter the password to access it. Please note that the password must contain at least 8 characters.
"Guest Wi-Fi network"- here you can configure the guest wireless network of your router.
"Beeline" TV - if you have activated the "Beeline" TV service, you need to select the router port to which you will connect the set-top box. If you view over-the-air channels on your computer or using an Xbox 360 console, then you don't need to configure anything.
To save the settings you entered, click the Save button.
6. Launch the browser, open the page http://login.beeline.ru
Fill the form:
Login - indicate your personal account number (type 0891234567);
Password - enter a password to access the Internet;
Click the Login button.
Firmware update and factory reset
Firmware update
Reset
Firmware update
Be careful when following the instructions in this section. In case of an error in the actions, a visit to the service center will be required to restore the device.
Or through the router's web interface. Click on the "Revert to factory default settings" button.
2. Open your browser and enter 192.168.1.1 in the address bar. You will be taken to a welcome page. Click Continue.
3. The router will prompt you to enter your username and password. Enter admin in the first field, and admin in the second. Click Continue.
4. Click on the “Advanced Settings” button.
5. In the top menu, select “Others”.
6.A page with the basic settings of the router will open. In the left menu, select “Software Update”. Click the "Select File" button and specify the location of the firmware file that you downloaded earlier.
7. After that, click the “Perform update” button.
8. Wait while the router performs a firmware update, this process takes approximately 5 minutes, after which the router must be rebooted and it will be ready for use.
Reset
Use a hard reset if you need to configure the device again (delete all user settings), there is no access to the web page of the router settings interface, after setting up the router, the Internet connection was not established or the access password was lost.
Attention! When performing a hard reset, all user settings will be reset to factory settings!
There is a recessed RESET (RESTORE) button on the device body, which allows you to reset the settings to factory settings. You can find the RESET, RESTORE button on the same side of the router case where the other connectors and buttons are located. In rare cases, the button may be located on the bottom of the router.
To reset the router to factory settings, follow these steps: Turn on the power to the router and wait until the device boots up completely. Press the RESET, RESTORE button using a pointed thin object (such as a paper clip) for 30 seconds, then release the button.
After this, the router will reboot with default settings (factory settings) and will need to be configured again.
You can also reset the setting through the MCPE platform
Connecting a router
Connect the cable that our installers installed in your apartment to the Internet (WAN) port, and connect your computer to any of the Ethernet (LAN) ports. You can also connect your PC to the router via a wireless network, but at the initial setup stage it is better to use a cable.
Setting up the router
Setting up a router on L2TP
Setting up a router on L2TP
"Home Internet"- in this section you configure the connection to the Beeline network. All configuration data necessary for connection is already contained in the router’s memory; you just need to enter your username and password in the appropriate fields.
"Beeline" TV - if you have activated the "Beeline" TV service, you need to select the router port to which you will connect the set-top box. If you view over-the-air channels on your computer or using an Xbox 360 console, then you don't need to configure anything.
1. Download the firmware. Current firmware version - 2.0.15: (22.2 MB)
To save the settings you entered, click the Save button.
Firmware update and factory reset
Firmware update
Reset
Firmware update
"Router Security"
First, determine the revision of the router!
1. Revision B1/B2/B3 with firmware versions from 1.2.100 to 1.2.119: current firmware 1.2.120
If the router revision B1/B2/B3 has a software version lower than 1.2.100 (1.2.99 and lower), then you need to update first to 1.2.100, THEN to the current firmware 1.2.120
For revision B5/B6, you need to update to firmware 1.2.254, then to the newer 1.2.255
If you have a D-Link DIR 300/NRU router revision B1/B2/B3/B5/C1 with factory firmware, you can update the firmware to customized one at the nearest D-Link service center, the update procedure is free, you will need the device itself and a valid subscription agreement.
Please note that services for restoring unsuccessfully flashed routers and returning from customized firmware to factory firmware are provided at the D-Link Service Center on a paid basis.
For routers revision C1, after a successful firmware update, you need to reset the router by pressing the RESET button on the side panel for 30 seconds. After this, perform the standard router setup.
Do not install firmware for DIR-300/NRU hardware revisions B1, B2, B3 on a DIR-300/NRU router with hardware revision B5. This leads to the router not working.
3. Open your browser and enter 192.168.1.1 in the address bar. The router will prompt you to enter your username and password. Enter admin in both fields. Click OK.
5. On the left side of the menu, go to the “System” section, then the “Software Update” subsection. Click on the “Select file” button and in the window that appears, select the file with the firmware. Click the "Update" button.
6. Wait while the router updates the firmware and reboots, this process may take up to 5 minutes. During this time, do not unplug the router from the power supply.
Reset
Use a hard reset if you need to configure the device again (delete all user settings), there is no access to the web page of the router settings interface, after setting up the router, the Internet connection was not established or the access password was lost.
Attention! When performing a hard reset, all user settings will be reset to factory settings!
There is a recessed RESET (RESTORE) button on the device body, which allows you to reset the settings to factory settings. You can find the RESET, RESTORE button on the same side of the router case where the other connectors and buttons are located. In rare cases, the button may be located on the bottom of the router.
To reset the router to factory settings, follow these steps: Turn on the power to the router and wait until the device boots up completely. Press the RESET, RESTORE button using a pointed thin object (such as a paper clip) for 30 seconds, then release the button.
4. You will be taken to the router quick setup page. Click on the "Advanced Settings" button.
D150L
Connecting a router
Connect the cable that our installers installed in your apartment to the Internet (WAN) port, and connect your computer to any of the Ethernet (LAN) ports. You can also connect your PC to the router via a wireless network, but at the initial setup stage it is better to use a cable.
Setting up the router
Setting up a router on L2TP
Setting up a router on L2TP
Open your browser and enter 192.168.1.1 in the address bar. The router will prompt you to enter your username and password. Enter admin in the first field and 1234 in the second. Click OK.
You will be taken to the router quick setup page. It consists of three sections, let’s look at the purpose of each of them:
"Home Internet"- in this section you configure the connection to the Beeline network. All configuration data necessary for connection is already contained in the router’s memory; you just need to enter your username and password in the appropriate fields.
“My Wi-Fi network” - here you can configure your router’s wireless network. In the Network name field, enter the name of your network, for example my_wifi, and in the Password field, enter the password to access it. Please note that the password must contain at least 8 characters.
"Beeline" TV - if you have activated the "Beeline" TV service, you need to select the router port to which you will connect the set-top box. If you view over-the-air channels on your computer or using an Xbox 360 console, then you don't need to configure anything.
1. Download the firmware. Current firmware version - 2.0.15: (22.2 MB)- here you can change the password to access your router.
To save the settings you entered, click the Save button.
After clicking the Save button, it will take approximately 1 minute for the router to establish a connection.
As soon as the router establishes a connection, you will see “Internet connected” opposite the Status line. Congratulations, you have fully configured your router to work on the Beeline network.
Firmware update and factory reset
Firmware update
Reset
Firmware update
Be careful when following the instructions in this section. In case of an error in the actions, a visit to the service center will be required to restore the device. It is recommended to flash the router by connecting the cable from the PC to any of the LAN ports. When flashing a router via Wi-Fi, there is a risk of getting an inoperative device that can only be restored in a service center, or cannot be restored at all.
1. Open your browser and enter 192.168.1.1 in the address bar. The router will prompt you to enter your username and password. Enter admin in both fields. Click OK.
2. You will be taken to the router quick setup page. Click on the "Advanced Settings" button.
3. On the left side of the menu, go to the “System” section, then the “Software Update” subsection. Click on the “Select file” button and in the window that appears, select the file with the firmware. Click the "Update" button.
4. Wait while the router updates the firmware and reboots, this process may take up to 5 minutes. During this time, do not unplug the router from the power supply.
Reset
Use a hard reset if you need to configure the device again (delete all user settings), there is no access to the web page of the router settings interface, after setting up the router, the Internet connection was not established or the access password was lost.
Attention! When performing a hard reset, all user settings will be reset to factory settings!
There is a recessed RESET (RESTORE) button on the device body, which allows you to reset the settings to factory settings. You can find the RESET, RESTORE button on the same side of the router case where the other connectors and buttons are located. In rare cases, the button may be located on the bottom of the router.
To reset the router to factory settings, follow these steps: Turn on the power to the router and wait until the device boots up completely. Press the RESET, RESTORE button using a pointed thin object (such as a paper clip) for 30 seconds, then release the button.
You can also reset via the router’s web interface. Open your browser and enter 192.168.1.1 in the address bar. The router will prompt you to enter your username and password. Enter admin in both fields. Click OK.
4. You will be taken to the router quick setup page. Click on the "Advanced Settings" button.
5. On the left side of the menu, go to the “System” section, then the “Configuration” subsection. Click the "Factory Reset" button.
N150L
Connecting a router
Connect the cable that our installers installed in your apartment to the Internet (WAN) port, and connect your computer to any of the Ethernet (LAN) ports. You can also connect your PC to the router via a wireless network, but at the initial setup stage it is better to use a cable.
Setting up the router
Setting up a router on L2TP
Setting up a router on L2TP
1. Open your browser and enter 192.168.1.1 in the address bar. The router will prompt you to enter your username and password. Enter admin in the first field and 1234 in the second. Click OK.
2. You will be taken to the router quick setup page. It consists of three sections, let’s look at the purpose of each of them:
"Home Internet"- in this section you configure the connection to the Beeline network. All configuration data necessary for connection is already contained in the router’s memory; you just need to enter your username and password in the appropriate fields.
“My Wi-Fi network” - here you can configure your router’s wireless network. In the Network name field, enter the name of your network, for example my_wifi, and in the Password field, enter the password to access it. Please note that the password must contain at least 8 characters.
"Beeline" TV - if you have activated the "Beeline" TV service, you need to select the router port to which you will connect the set-top box. If you view over-the-air channels on your computer or using an Xbox 360 console, then you don't need to configure anything.
1. Download the firmware. Current firmware version - 2.0.15: (22.2 MB)- here you can change the password to access your router.
To save the settings you entered, click the Save button.
Attention! When performing a hard reset, all user settings will be reset to factory settings!
There is a recessed RESET (RESTORE) button on the device body, which allows you to reset the settings to factory settings. You can find the RESET, RESTORE button on the same side of the router case where the other connectors and buttons are located. In rare cases, the button may be located on the bottom of the router.
To reset the router to factory settings, follow these steps: Turn on the power to the router and wait until the device boots up completely. Press the RESET, RESTORE button using a pointed thin object (such as a paper clip) for 30 seconds, then release the button.
You can also reset via the router’s web interface. Open your browser and enter 192.168.1.1 in the address bar. The router will prompt you to enter your username and password. Enter admin in both fields. Click OK.
4. You will be taken to the router quick setup page. Click on the "Advanced Settings" button.
5. On the left side of the menu, go to the “System” section, then the “Configuration” subsection. Click on the "Reset" button.
Wi-Fi router "Beeline"
| Default wireless network name (SSID) | Beeline_router |
|---|---|
| Default wireless (Wi-Fi) password |
By joining via promotion "House of the 21st century+" and they brought it to your apartment on the day of connection Wi-Fi router Smart Box. As a rule, all equipment configuration is carried out by the installer during connection. There are situations when, for some reason, the settings of your router are lost and you need to reconfigure your Smart Box. Instructions for this are provided below.
Basic parameters of the Smart Box router:
- Router address - 192.168.1.1
- Latest firmware - 2.0.11
- Username to access the device - admin
- The password to access the device is admin
- Network name (SSID) - Smart_box-XXXXXX (where X are characters unique to each device)
- The default wireless network (Wi-Fi) key is no key
Connecting a Smart Box router
1. Insert the cable laid into the apartment by our installers into the WAN port, and connect the computer with the patch cord (cable) from the router kit to any of the LAN ports. You can also connect your computer to the router via Wi-Fi, but at the first stage it is still better to use a cable connection.
Connection setup
2. So, you have connected the router to the computer and to the cable from the entrance. Next, open your browser and enter 192.168.1.1 in the address bar. You should be taken to a welcome page. Click the button Continue.
3. The setup program will prompt you to enter a username and password. Enter in the first field admin, and in the second admin. Click Continue.
4. You will now be taken to the main menu Click on the button Quick setup.
"Home Internet"— in this section you set up a connection to the Internet, all the data necessary for connection is contained in the device’s memory, you just need to enter your login and password from the contract in the appropriate fields.
“Wi-Fi network of the router”— in this section you have the opportunity to set up a wireless home Wi-Fi network. In field Network name you need to come up with and enter the name of your network, for example free_wifi, and enter the network key in the password column in order to protect your connection from unauthorized access. Please note that the network key must be at least 8 characters including numbers and letters of the Latin alphabet.
"Guest Wi-Fi network"— it is possible to set up a guest Wi-Fi network.
"Beeline" TV— if you are also a television subscriber, you need to select the port (LAN1, LAN2, LAN3, LAN4) to which you will connect the set-top box. If you watch channels on a PC or using an Xbox 360, you do not need to configure port forwarding.
To save the settings, click the button Save.
6. It will take about 1 minute to save the settings and connect to the Internet router.
Once the connection is established, opposite the line Status a message will appear "Internet connected". Congratulations! Smart Box router fully configured for networking Beeline.
Smart Box firmware
First, download the firmware - smart_box_2.0.11.img
1. Open the browser and go to page 192.168.1.1? enter your login admin, password admin and press the button Continue.
2. Click on the button Advanced settings
4. A page with advanced router settings will appear. In the menu on the left, click Software Update. Press the button Choose File and use browse to select the location of the downloaded file. Then you can click the button Perform an update.
5. Wait until the device completes the firmware update, it takes about 5 minutes, after which the router needs to be rebooted (pull out and reinsert the router's power cable). Your Smart Box is ready to use.